Heat Exchanger Design – Calculations, 3D Model and Fabrication Drawings
SLETEC carries out mechanical heat exchanger design for shell and tube units and air-cooled exchangers, taking a thermal data sheet through to code calculations and drawings a workshop can build from. We also check and rerate existing exchangers when operating conditions change.
We provide mechanical design of shell and tube exchangers and air coolers: tubesheet, channel, shell, expansion joint, nozzle and support calculations with fabrication drawings.
Also searched as: heat exchanger drawing, cooler, condenser.
Last updated:
Request Engineering Support
Typical response within 24 hours · Confidentiality assured
What we deliver
Send us your data sheet, sketch or old drawing on WhatsApp (+966 55 545 8298) or email (enquiry@sletec.com) for a fixed-price quote, usually within 24 hours.
What we need from you for shell and tube heat exchanger design
Mechanical design starts after the thermal design is fixed. The TEMA data sheet sets the front head, shell and rear head type (for example BEM, AES or AKT), and that choice drives the whole calculation: a fixed tubesheet needs a differential expansion check, while a floating head or U-tube bundle does not.
If you only have a process duty and no thermal design, tell us early so the scope can include sizing before the mechanical work begins.
- Design pressure and temperature on shell side and tube side, including any vacuum case
- TEMA type, TEMA class (R, C or B) and tube layout, pitch and length
- Materials for shell, channel, tubes, tubesheet and gaskets, with corrosion allowances
- Nozzle sizes, ratings and external nozzle loads from the piping stress engineer
- Wind, seismic and stacking arrangement if units are mounted one above the other
TEMA design and code checks we run
Each component is checked against the governing code and the TEMA class. The table shows where the main checks come from.
| Code or standard | What it governs |
|---|---|
| ASME VIII Div. 1 | Shell, channel, head and nozzle thickness; tubesheet design; flanged-and-flued or bellows expansion joints |
| TEMA (R, C or B) | Minimum thicknesses, baffle and support plate spacing, tie rods, tube-to-tubesheet joint details, tolerances |
| API 661 | Air cooler header boxes (plug or cover-plate type), tube bundle frame, allowable nozzle loads, fan and structure interfaces |
| WRC 537 / WRC 107 | Local stresses at nozzles and support attachments under piping loads |
| Client specifications | SAES / SAMSS, SABIC or ADNOC requirements and the project specification where they apply |
Heat exchanger rerating and problems found on existing units
Rerating means confirming that an existing exchanger can run at new pressure or temperature conditions. We take the original data sheet and drawings, apply measured thicknesses from inspection, and recalculate the maximum allowable working pressure for each part. Our references include a shell-and-tube rerating to PD 5500 and a bellows replacement assessed to TEMA and ASME.
Common findings on older units include tubesheet thinning at the pass partition groove, cracked tube-to-tubesheet welds from thermal cycling on fixed-tubesheet designs, and nozzles overloaded by piping that was rerouted after the original design. Each finding is written up with a recommended repair or operating limit.
How an exchanger job runs
We review your data sheet and confirm the design basis in writing, then issue calculations, a 3D model and the GA drawing for comment before detailing the tube bundle, baffles and supports. Every issue goes through self-check, independent check and approval. For related scope, see our heat exchanger design service and the static equipment design project.
Related engineering topics
pressure vessel design, static equipment design, nozzle local stress FEA and pressure vessel FEA ASME VIII Div 2.
Frequently Asked Questions
Can you design a heat exchanger for our project?
Yes. We prepare calculations and drawings to TEMA, ASME VIII, API 661 and your project specification.
Do you take small jobs?
Yes. Single drawings, one calculation or a check of an existing design are welcome.
Which countries do you serve?
Saudi Arabia, UAE, Qatar, Oman, Kuwait, Bahrain and worldwide.
Related pages
Serving all GCC countries
Send your sketch, photo or PDF today
One drawing or a complete design package — we reply with a fixed-price quote, usually within 24 hours.
Request Engineering Support
Typical response within 24 hours · Confidentiality assured