Lifting Lug Calculation – Calculations, 3D Model and Fabrication Drawings
A lifting lug calculation from SLETEC checks every failure mode of the lug, its weld and the parent shell or beam, and comes with a drawing that matches the shackle you will actually use. We handle single lugs for a workshop lift as well as full lifting point sets for vessels, skids and modules.
We calculate and draw lifting lugs, padeyes, tailing lugs and trunnions for vessels, skids and structures, often within one or two working days.
Also searched as: lifting lug, padeye, trunnion.
Last updated:
Request Engineering Support
Typical response within 24 hours · Confidentiality assured
What we deliver
Send us your data sheet, sketch or old drawing on WhatsApp (+966 55 545 8298) or email (enquiry@sletec.com) for a fixed-price quote, usually within 24 hours.
Inputs for a padeye calculation
A padeye is only as good as the load case behind it. Before sizing the plate we fix the lift weight, centre of gravity and rigging arrangement, because the sling angle decides how much of the load arrives out of plane.
Where the rigging plan is not yet final, we state the assumed sling angles and contingency factors on the calculation cover so the rigging contractor can confirm them.
- Lifted weight with a weight contingency and the centre of gravity position
- Number of lifting points, sling angles and whether a spreader bar is used
- Shackle size and type, so pin hole, jaw width and plate thickness are compatible
- Parent material and thickness at the attachment, plus any reinforcing pad
- Lift type: workshop lift, site erection, upending with a tailing lug, or offshore lift
Lifting lug design checks and governing codes
Pin-connected plates fail in several ways, so we check each one rather than relying on a single stress figure. The code is chosen to suit the lift and the client specification.
| Code | What it governs |
|---|---|
| ASME BTH-1 | Design category and service class, design factors, tension at the pin hole, double-plane shear, bearing and cheek plate checks |
| AISC 360 | Fillet and full-penetration weld strength and base metal checks at the lug attachment |
| DNV-ST-N001 | Dynamic and skew load factors and padeye checks for marine and offshore lifts |
| WRC 107 / WRC 537 | Local stress in a vessel shell or head where the lug or trunnion is welded |
When lifting lug FEA is worth doing
Hand calculations cover most lugs on thick plate or beams. FEA is justified when the lug sits on a thin shell, a cone or a nozzle region, or when a tailing lug sees a load that changes direction as a column is upended from horizontal to vertical. A model shows how far the stress spreads into the shell and whether a wrap plate or stiffening ring is needed. See our structural platform FEA project for the type of reporting we issue.
Problems we find on existing lugs
Reused lugs often have a pin hole worn oval, a shackle that is too small for the hole so the pin bends, or a plate too thick for the shackle jaw. We also see lugs welded parallel to the sling direction when the sling actually pulls at an angle, which loads the weld in peel. Each of these is noted with a pass or fail and a corrected detail. Related work sits under lifting and rigging calculations.
Related engineering topics
lifting and rigging calculations, lifting beam design and skid design.
Frequently Asked Questions
Can you design a lifting lug for our project?
Yes. We prepare calculations and drawings to ASME BTH-1, DNV and your project specification.
Do you take small jobs?
Yes. Single drawings, one calculation or a check of an existing design are welcome.
Which countries do you serve?
Saudi Arabia, UAE, Qatar, Oman, Kuwait, Bahrain and worldwide.
Related pages
Serving all GCC countries
Send your sketch, photo or PDF today
One drawing or a complete design package — we reply with a fixed-price quote, usually within 24 hours.
Request Engineering Support
Typical response within 24 hours · Confidentiality assured