Equipment Design

Silo and Hopper Design – Calculations, 3D Model and Fabrication Drawings

SLETEC provides silo design for cement, grain, fly ash, powders and plastic pellets, covering the bulk solid loads, the steel shell and hopper, the support structure and the drawings needed to fabricate and erect it.

We design steel silos, hoppers and bins with flow and pressure calculations, structural design and fabrication drawings.

Also searched as: cement silo, grain silo, hopper.

Fixed-price quote in 24 hoursSmall jobs welcomeAPI · ASME · AISC · Saudi Aramco

Last updated:

Request Engineering Support

Typical response within 24 hours · Confidentiality assured

SLETEC portfolio

Project Evidence — API Storage Tanks, Silos & Bulk Systems

Selected engineering evidence from SLETEC projects. Client names and identifiers are withheld for confidentiality.

Silo General ArrangementDesign data, nozzle schedule, material specification and fabrication basis for a cement silo.
Particle Flow & Silo DischargeMaterial recirculation, discharge behaviour and unloading validation.
Silo Unload ReviewSilo unload process — particle flow behaviour.

Scope

Tank sizing, shell/roof/bottom design, nozzles, anchors, access systems

Codes

API 650 · API 620 · API 2000 · ASCE 7

Deliverables

Calculations, GA & fabrication drawings, FEA reports

Send us your data sheet, sketch or old drawing on WhatsApp (+966 55 545 8298) or email (enquiry@sletec.com) for a fixed-price quote, usually within 24 hours.

Silo structural design starts with the stored material

Wall pressures in a silo depend on the material far more than on the volume. Bulk density, wall friction and the angle of internal friction set the Janssen pressure distribution, and the same silo can see very different loads when it stores cement and when it stores grain.

We ask for the material properties, filling and discharge rates, the discharge outlet position and any aeration or pneumatic filling. If test data is not available, values from the EN 1991-4 tables are used and stated as assumptions.

Codes for EN 1991-4 silo loads and steel design

EN 1991-4 places each silo in an Action Assessment Class based on capacity and eccentricity. A higher class requires more refined pressure calculations, including patch loads and eccentric discharge.

Governing documents for a steel silo
CodeWhat it governs
EN 1991-4Filling and discharge pressures, patch loads, eccentric discharge, hopper pressures
EN 1993-4-1Steel silo shell, hopper and transition ring strength and buckling
ACI 313Concrete silos and their design loads
ASCE 7 or local codeWind and seismic loads on the silo and its support columns

Hopper design and flow pattern

The hopper angle and outlet size decide whether the silo runs in mass flow or funnel flow. Funnel flow can leave stagnant material and cause ratholes, while mass flow raises the switch pressure at the transition. We check the hopper geometry against the material and size the transition ring for the combined hoop and meridional forces.

Problems found in existing cement silo design

Existing cement silos often show buckling near the transition, cracked column-to-shell connections, or overpressure damage to the roof when the filter or relief valve is undersized for pneumatic filling. Our silo CFD engineering project shows how particle flow modelling can explain discharge problems before a structural fix is chosen.

Frequently Asked Questions

Can you design a silo and hopper for our project?

Yes. We prepare calculations and drawings to EN 1991-4, ACI 313 and your project specification.

Do you take small jobs?

Yes. Single drawings, one calculation or a check of an existing design are welcome.

Which countries do you serve?

Saudi Arabia, UAE, Qatar, Oman, Kuwait, Bahrain and worldwide.

Send your sketch, photo or PDF today

One drawing or a complete design package — we reply with a fixed-price quote, usually within 24 hours.

Request Engineering Support

Typical response within 24 hours · Confidentiality assured